common:connectorpinouts_connectionoptions

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
common:connectorpinouts_connectionoptions [2017/09/06 19:40] Pedro Ramilocommon:connectorpinouts_connectionoptions [2022/12/21 18:59] (current) Pedro Ramilo
Line 1: Line 1:
 ===== Connection Diagrams and Connector Pinouts ===== ===== Connection Diagrams and Connector Pinouts =====
  
-All Seed Robotics models come standard with USB interface and one main interface (the main connector), with a logical interface selected by the customer: One Wire TTLFull Duplex TTL or RS485.\\ +All Seed Robotics models come standard with USB interface and one main interface (the main connector), with a logical interface (by default this is RS485; users can also request One Wire TTL or Full Duplex TTL ).\\ 
-In addition an [[dh4d:bluetooth| Optional Bluetooth Module]] can be installed on the unit and connects to any terminal that supports the Bluetooth SPP (Serial Port) Profile.+Previously an [[eros:bluetooth_module| Optional Bluetooth Module]] could also be installed on the unit and connects to any terminal that supports the Bluetooth SPP (Serial Port) Profile.
  
 Below we detail the connector types for the units and connection diagrams with the most commonly used tools. Below we detail the connector types for the units and connection diagrams with the most commonly used tools.
  
-==== About Supplying Power ====+==== Supplying Power ====
  
-External power must **always be supplied through the main connector port** (the one with the 3 pin or 4 pin connector).\\ +External power must **always be supplied through the main connector port** (the one with the 3 pin or 4 pin connector on the back of the unit).\\ 
-**If you intend on using other interfaces for control (such as USB or Bluetooth), power must still be applied through this connector on the VDD and GND pins.**+**If you intend on using other interfaces for control such as USB or Bluetooth, power must still be applied through this connector on the VDD and GND pins.**
  
 Acceptable voltage range is typically 9V~24V. Please refer to the documentation of your specific model for the exact voltage range accepted. Acceptable voltage range is typically 9V~24V. Please refer to the documentation of your specific model for the exact voltage range accepted.
  
 +==== Main Connector ====
  
-==== Main Connector: One Wire Serial TTL Interface ====+**The main connector is located at the back of the unit (it's a 3 or 4 in connector). It is the via through which you command and control your unit and is the most important connection for power and control.**
  
-The One Wire TTL Serial interface enables daisy chained connection of multiple units. +(connecting via USB or other means is optional, and usually intended for Diagnostics and maintenance; regular operation and control is done via this Main Connector).
-This interface operates natively at 3.3V but it is tolerant to 5V or higher voltages making it compatible with virtually all devices operating at TTL level.+
  
-This interface option is directly compatible with Robotis Dynamixel AX, MX series of servos. It can also connect to XL and XM series of servos provided you create a necessary adapter cable or board to connect them.+Please select the type of interface in your main connector (this should be shown in our Quotation; by defaut it is RS485)
  
-It is important to note that this connection uses only 1 wire for DATA, which means a special adapter is required to control the line switching between RX and TX.\\ +  * [[common:connectioninterface_rs485|RS485 interface]] 
-The most common adapters and connection methods are shown below. +  * [[common:connectioninterface_TTLOnewire|One Wire TTL interface]] 
- +  [[common:connectioninterface_Fullduplex_TTL|Full Duplex TTL Interface]]
-===== Robotis USB2Dynamixel and SMPS2Dynamixel ===== +
- +
-{{:common:connect-using-usb2dyn.jpg?direct&400|}} +
- +
-===== Xevel Labs USB2AX ===== +
- +
-{{:common:connect-using-usb2ax.jpg?direct&400|}} +
- +
-===== Connecting to an existing Dynamixel Servo Chain or Dynamixel based Robot ===== +
- +
-{{:common:connect-to-existing-dynamixel-chain.jpg?direct&400|}} +
- +
-===== Connector Pinout for TTL signal level interface ===== +
- +
-{{:dh4d:connector-pinout-one-wire-ttl.png?direct&400|}} +
- +
- +
-==== Main Connector: RS485 Serial Interface ==== +
- +
-The RS485 interface uses a differential pair to operate in half duplex mode. +
-In this mode operation on a daisy chained environment is possible. +
- +
-This connector option is directly compatible with Robotis MX, RX series of servos. It can also connect to XM series of servos provided you create a necessary adapter cable to connect them (the XM series uses a different connector, but the signal levels/interface is the same - RS485). +
- +
-**IMPORTANT: in RS485, even though communication is done through a differential pair, __GND must also be connected__ in common between the Seed Robotics unit and the MCU.** Failure to do so may result in unreliable communication and potential damage to the units. +
- +
-===== Robotis USB2Dynamixel and SMPS2Dynamixel ===== +
- +
-{{:common:connect-using-usb2dyn.jpg?direct&400|}} +
- +
-===== Connecting to an existing Dynamixel Servo Chain or Dynamixel based Robot ===== +
- +
-{{:common:connect-to-existing-dynamixel-chain.jpg?direct&400|}} +
- +
-===== Connect to an RS485 converter ===== +
- +
-The diagram below is generic: it is designed in a way to suit all major RS485 converters.\\ +
-If you have any question regarding connection to your specific converter, please contact support@seedrobotics.com and we'll be happy to assist you. +
- +
-When selecting an RS485 converter, please observe the maximum baud rate of the converter. Bear in mind the default communication speed on the main port is 1Mbps. While it is possible to reduce it to a much lower value (115.2/57.6/9.6 kbps), we recommend 1Mbps or higher for best performance. +
- +
-{{:common:connect-via-rs485.jpg?direct&400|}} +
- +
-===== Connector Pinout for RS485 signal level interface ===== +
- +
-{{:dh4d:connector-pinout-rs485.png?direct&400|}}+
  
  
Line 77: Line 31:
 This connector is a standard micro-USB type connector. Once connected to the host, it will create a Virtual Serial Port. This connector is a standard micro-USB type connector. Once connected to the host, it will create a Virtual Serial Port.
  
-When connecting via USB, you must still apply power through the Main Connector as shown in the diagram below.\\ +When connecting via USB, you must still apply power through the Main Connector as shown in the diagram below. Failure to do so will result in the Actuators not responding and the hand not moving as they will not be powered.
-Failure to do so will result in the Actuators not responding and the hand not moving as they will not be powered.+
  
-**IMPORTANT:** you can connect via Bluetooth even if your unit is already connected via any of the other ways shown above.+{{:common:connect-via-usb.jpg?direct&400|}}
  
-{{:common:connect-via-usb.jpg?direct&400|}}+** As an alternative, you can apply External Power by simply connecting the normal Main Connector (i.e. if you have PC Interface Cable set from Seed Robotics (or something similar) to control your unit, simply connect it, and apply power as usual)**
  
-By default the firmware is configured to expose the USB Console over USB. This means that control using the Dynamixel protocol is not enabled by default on the USB port (although it can be enabled if required).\\ 
 For more information, see the [[eros:settingup_usbconnection|EROS: Setting up the USB Connection]] documentation. For more information, see the [[eros:settingup_usbconnection|EROS: Setting up the USB Connection]] documentation.
  
Line 93: Line 45:
  
 **IMPORTANT:** you can connect via Bluetooth even if your unit is already connected via any of the other ways shown above. The unit can simultaneously accept commands through the main port and the Bluetooth interface.\\ **IMPORTANT:** you can connect via Bluetooth even if your unit is already connected via any of the other ways shown above. The unit can simultaneously accept commands through the main port and the Bluetooth interface.\\
-This is especially convenient for **online diagnostics** and maintenance.+This is especially convenient for **online, wireless diagnostics** and maintenance.
  
 When connecting via Bluetooth, you must apply power through the Main Connector as shown in the diagram below.\\ When connecting via Bluetooth, you must apply power through the Main Connector as shown in the diagram below.\\
Line 101: Line 53:
  
 By default the firmware is configured to expose the Console over Bluetooth. This means that control using the Dynamixel protocol is not enabled by default on the Bluetooth port (although it can be enabled if required).\\ By default the firmware is configured to expose the Console over Bluetooth. This means that control using the Dynamixel protocol is not enabled by default on the Bluetooth port (although it can be enabled if required).\\
-For more information, see the [[eros:consolecommands|List of Console Commands (for EROS architecture)]].+For more information, see [[eros:bluetooth_module|Using the Bluetooth Interface Module]].
  
  

Copyright © 2015-2023 Seed Robotics Ltd

  • common/connectorpinouts_connectionoptions.1504726843.txt.gz
  • Last modified: 2017/09/06 19:40
  • by Pedro Ramilo