Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
dh4d:home [2017/04/10 10:06]
pedro.ramilo
dh4d:home [2019/10/30 08:11]
pedro.ramilo
Line 1: Line 1:
-===== SR-RH4D Hand =====+===== RH4D Advanced Manipulator ​=====
  
 {{:​dh4d:​infograma_com_a_mao_e_as_setas_a_indicar_as_funcoes-02.png?​nolink&​600|}} {{:​dh4d:​infograma_com_a_mao_e_as_setas_a_indicar_as_funcoes-02.png?​nolink&​600|}}
  
  
-The [[http://​www.seedrobotics.com/​rh4d-ares-hand.html|Seed Robotics SR-RH4D]] (formerly the SR-DH4D) Hand is an under actuated, advanced Robotic Hand, offering 11DoF total with 4 actuators. (4 actuated DoF)+The [[http://​www.seedrobotics.com/​rh4d-ares-hand.html|Seed Robotics SR-RH4D]] (formerly the SR-DH4D) Hand is an under actuated, advanced Robotic Hand, offering 11DoF total with 4 actuated DoF (using 4 smart actuators).
-The hand includes five microprocessors:​ a 32 bit ARM Cortex M4 for High Level control and communication with external peripherals and four ATMEGA88 for distributed low level motion control. All external communication is handled by the ARM processor at 96Mhz.+
  
-The hardware ​is designed to receive ​commands from multiple ​simultaneous protocols and interfaces. USB and optinally Bluetooth are available and a third interface (the main connector) can be set up as One Wire Half Duplex TTL (0-3.3V~5V), ​RS485, Full Duplex ​TTL (0-3.3V~5V). +The unit is capable of receiving ​commands ​simultaneously ​from multiple interfacesmain connector (RS485 ​or TTL), USB and optionally Bluetooth
- + 
-Control is performed using a memory mapped paradigm: Control Tables enable querying and setting a number of parameters that control and provide real-time feedback on the unit.\\ +
-Reading and writing the control table is done using the Robotis Dynamixel Protocol (a Serial protocol) or through the Seed Robotics own Text protocol.\\ +
-This Control table is structured to emulate the original Robotis MX series servo (the version that works under Dynamixel V1 protocol), making it compatible out of the box with Robotis products ​and frameworks such as Robotis OP/OP2 Robot or any Dynamixel based Robot+
- +
-A versatile, built in, [[dh4d:​consolecommands|console interface]] is also available and enables console enables advanced configuration,​ diagnostics and control. This is especially useful if you have the Bluetooth module installed as it enables real-time diagnostics and tuning without having to interrupt operation of the unit. By default, the console functionality is also available over USB.+
  
 === NOTICE: Change from the Ares to Eros Architecture === === NOTICE: Change from the Ares to Eros Architecture ===
  
-As of March 1st 2017, we began shipping the RH4D with the new Eros Architecture ​that already powers the RH7D.\\ +As of March 1st 2017, all RH4D units are built on the scalable ​Eros Architecture ​(used in all other Seed Robotics products).\\ 
-Our goal is to have all our units under one common, modular architecture. +Information ​about the transition ​is available ​in the document [[eros:​whatsnewvsares|EROS vs ARES architecture:​ What's new and What's changed]]. 
- +In the interest of organizationwe have moved the documentation related ​to models manufactured before that that [[ares:​legacy_introduction|(the old Architecture ​(ARES)) to separatelegacy ​section]].\\
-We have published information ​about the transition in the document [[eros:​whatsnewvsares|EROS vs ARES architecture:​ What's new and What's changed]] +
- +
-If just purchased your unitplease scroll down to the section pertaining ​to the EROS Architecture.\\ +
-If you own previous unitplease refer to the ARES section.+
  
  
Line 29: Line 19:
  
   * [[dh4d:​unpacking+assembly|Unpacking and Mechanical Assembly]]   * [[dh4d:​unpacking+assembly|Unpacking and Mechanical Assembly]]
 +  * [[common:​connectorpinouts_connectionoptions|Connection Diagrams and Connector Pinouts]]
  
- +  * [[rh4d:​DynamixelIDsandCOMMsettings|Dynamixel Protocol: Default IDs and Communication Settings]]
-==== Testing your Unit ====+
   * [[dynamixel:​dynwzrd_ctrltables|Add support for RH4D in Robotis/​Roboplus Dynamixel Wizard]]   * [[dynamixel:​dynwzrd_ctrltables|Add support for RH4D in Robotis/​Roboplus Dynamixel Wizard]]
-  * Using the Darwin-OP Framework: [[dh4d:​DarwinOPFramework|Operation with the Darwin-OP Framework]] 
  
-==== - Eros Architecture ​==== +==== Command and Control ​Architecture ====
-Units built on or after March 1st 2017.+
  
-=== Command and Control Architecture === +  ​* [[eros:​dynamixelcontroltables|RH4D Control Tables]]
- +
-  ​* [[eros:​dynamixelcontroltables|EROS Control Tables]]+
   * [[dynamixel:​Dynamixel Protocol|Controlling the unit using the Dynamixel Protocol]] (main connector interface)   * [[dynamixel:​Dynamixel Protocol|Controlling the unit using the Dynamixel Protocol]] (main connector interface)
-  * [[seedstpprotocol:​Control_using_stp|Control using the Seed Robotics Simple Text Protocol (STP)]] (USB or Bluetooth interface+  * [[seedstpprotocol:​Control_using_stp|Control using the Seed Robotics Simple Text Protocol (STP) and Online Diagnostics and Maintenance]] (USB or Bluetooth interface)
-  * [[eros:​consolecommands|Complete List of Console Commands]] (to be used in the USB or Bluetooth console)+
  
 +=== The Console ===
  
-=== Special configuration features === +EROS units expose a Serial Console through which you can perform a number of queries, obtain real time diagnostics and also control the unit.
-  * [[eros:​1023and4095positionrange|1023 (10bit) vs 4095 (12bit) position resolution]]+
  
 +By default the firmware exposes the Serial Console on the USB Virtual Serial Port and on the Bluetooth interface (if optionally installed).\\
 +Use of the Console can be done simultaneously while controlling your unit through the main connector and while connected to your robot. This enables real time diagnostics and online application of corrective measures.
  
-==== - Ares Architecture - ==== +  * [[eros:​consolecommands|Complete List of Console Commands]] (to be used in the USB or Bluetooth console)
-Units built before March 1st 2017.+
  
-=== Command and Control Architecture === 
  
-  * [[dh4d:​DynamixelIDsandCOMMsettings|Dynamixel Protocol: Default IDs and Communication Settings]] +=== Special configuration features === 
-  * [[dynamixel:​Dynamixel Protocol|Controlling the unit using the Dynamixel Protocol]] (main connector interface) +  * [[eros:​1023and4095positionrange|1023 (10bit) ​vs 4095 (12bit) position resolution]]
-  * [[seedstpprotocol:​control_using_stp|Controlling the unit using Seed Robotics Simple Text Protocol (STP)]] (USB and Bluetooth connections) +
-  * [[dh4d:​DynamixelControlTables|RH4D Control Tables]] +
- +
-  * [[dh4d:​usbconsole|USB Interface: Console for Control and Diagnostics]]  +
-  * [[dh4d:​bluetooth|Bluetooth Interface: Console for Control and Diagnostics (optional)]] +
-  * [[dh4d:​consolecommands|List of RH4D Console Commands]] +
- +
-  * [[dh4d:​1023and4095positionrange|Configuring the SR-DH4D for 1023 (10bit) ​or 4095 (12bit) position resolution]] +
- +
- +
-==== - Common Documentation - ====+
  
 === Robots and Frameworks === === Robots and Frameworks ===
Line 78: Line 52:
 === In-depth information === === In-depth information ===
  
-  * [[dh4d:connector_pinouts|Connector Pinouts and Part numbers]]+  * [[common:connectorpinouts_connectionoptions|Connector Pinouts and Part numbers]]
  
  
Line 98: Line 72:
 ==== Maintenance ==== ==== Maintenance ====
  
-  * [[dh4d:​firmware_upgrade|Ares units: Upgrading your Firmware]] 
   * [[eros:​upgrademainboard_fw|EROS units: Upgrading the main board Firmware]]   * [[eros:​upgrademainboard_fw|EROS units: Upgrading the main board Firmware]]
-  * [[eros:actuators:​upgrading_fw|EROS units only: Upgrading the Actuators'​ firmware]]+  * [[eros:seedactuators:​upgrading_fw|EROS units only: Upgrading the Actuators'​ firmware]]
  
-  * [[dh4d:​led_errorcodes|LED Error codes]] 
   * [[dh4d:​maintenance|Maintaining your Unit in top working condition]]   * [[dh4d:​maintenance|Maintaining your Unit in top working condition]]
  

Copyright © 2015-2019 Seed Robotics Ltd

  • dh4d/home.txt
  • Last modified: 2019/10/30 08:11
  • by pedro.ramilo